Skip to main content

Measuring and alignment at your location

From the shaft alignment of a pump to the flatness of a wind turbine flange: our specialists measure with our own laser and measuring equipment, align directly where needed and advise on the next steps.

Request a measurement
Call +31 341 424 326
  • 45 years of experience in industry
  • Our own laser and measuring equipment
  • Measuring, alignment and advice
  • Equipment also available to rent or buy
Flatness measurement on a production line on site

What we measure

A selection of the measurements and alignments we carry out on site. Your situation not listed? Get in touch — there is often a solution.

Shaft alignment

Shaft alignment

Aligning motors, pumps, fans, compressors and complete machine trains with a laser alignment system. A well-aligned machine vibrates less, uses less energy and spares bearings, seals and couplings.

For example: Pumps, motors, compressors, machine trains
Request a measurement
Flatness, squareness, level and straightness

Flatness, squareness, level and straightness

Measuring machine beds, foundations, guideways and frames for flatness, squareness, level and straightness. This gives a machine a correct base, before assembly or when tracing deviations.

For example: Machine beds, foundations, guideways, frames
Request a measurement
Flange flatness and parallelism

Flange flatness and parallelism

Measuring the flatness and parallelism of large flanges, for example of wind turbine towers and tower segments, before assembly or after re-machining.

For example: Wind turbines, tower segments, large flange connections
Request a measurement
Centreline and bores

Centreline and bores

Measuring and aligning centrelines and bores, for example of bearing housings, stern tubes, turbines and compressor parts.

For example: Bearing housings, stern tubes, compressors, turbines
Request a measurement
Rolls and rollers

Rolls and rollers

Aligning rolls and rollers parallel to each other and measuring their profile to a thousandth of a millimetre, in paper, printing, film, aluminium and steel production lines.

For example: Paper, printing, film, aluminium, steel
Request a measurement
Runout, concentricity and eccentricity

Runout, concentricity and eccentricity

Measuring runout, concentricity and eccentricity of shafts, rolls and spindles, to detect imbalance, vibration and uneven wear.

For example: Shafts, rolls, spindles
Request a measurement
Calibration of machine tools

Calibration of machine tools

Measuring the positioning accuracy and repeatability of milling machines and lathes with laser interferometry, so that deviations become visible and can be corrected.

For example: Milling machines, lathes, machining centres
Request a measurement
Alignment of portable machining equipment

Alignment of portable machining equipment

Setting up and aligning portable boring, milling and turning machines accurately, so that on-site machining stays within tolerance.

For example: Boring, milling, turning and drilling on site
Request a measurement

For which industry?

Our experience is broad. A few examples per industry:

Wind energy

  • Flatness and parallelism of flanges
  • Aligning tower segments
  • Straightness and plumbness of towers
  • Shaft alignment of the drive train
  • Deformation and alignment errors due to wind load

Mechanical engineering, repair and overhaul

  • Milling machines and lathes
  • Aligning centrelines and bores
  • Parts of large compressors
  • Wheel bearings and crane rails
  • Turbines and rotors
  • Calibration of machine tools with laser interferometry

On-site machining

  • Setting up and aligning portable boring, milling, turning and drilling machines

Shipbuilding

  • Stern tube
  • Rudder
  • Drive shaft and bearings
  • Crankshaft bearings

Paper, printing, aluminium and steel

  • Parallelism of rolls
  • Roll shape
  • Roll profile
  • Assembly and alignment of cardan shafts

Wood and furniture industry

  • Tenoners and sawmill machines
  • Laminated multi-daylight presses

How it works

Step 1

Request

Tell us what needs to be measured or aligned: the machine, dimensions, required accuracy and any photos.

Step 2

Preparation

We choose the right measuring method and equipment and schedule the measurement, for example during a planned shutdown.

Step 3

Measuring and alignment

Our specialist measures at your location and aligns directly where needed.

Step 4

Results and advice

You receive the measurement results, with advice on any next steps. If required, we prepare a measurement report (optional, at extra cost).

Prefer to measure yourself?

Much of the equipment we measure with is also available to buy or rent.

Request a measurement

Fill in the form and we will contact you as soon as possible. Prefer to talk directly?

Phone
+31 341 424 326

Email

Tell us what needs to be measured or aligned. The more we know in advance — the machine, dimensions, required accuracy and any photos — the better we can prepare the measurement. We will contact you as soon as possible.

Please enter your name.
Please enter the company name.
Please enter a valid email address.
Invalid Input
Invalid Input
What needs to be measured or aligned?(*)
What needs to be measured or aligned?







Please choose at least one subject.
Briefly describe what needs to be measured.
Invalid Input
Invalid Input